jammy (8) mkswap.8.gz

Provided by: util-linux_2.37.2-4ubuntu3_amd64 bug

NAME

     mkswap - set up a Linux swap area

SYNOPSIS

     mkswap [options] device [size]

DESCRIPTION

     mkswap sets up a Linux swap area on a device or in a file.
     The device argument will usually be a disk partition (something like /dev/sdb7) but can
     also be a file. The Linux kernel does not look at partition IDs, but many installation
     scripts will assume that partitions of hex type 82 (LINUX_SWAP) are meant to be swap
     partitions. (Warning: Solaris also uses this type. Be careful not to kill your Solaris
     partitions.)
     The size parameter is superfluous but retained for backwards compatibility. (It specifies
     the desired size of the swap area in 1024-byte blocks. mkswap will use the entire
     partition or file if it is omitted. Specifying it is unwise - a typo may destroy your
     disk.)
     After creating the swap area, you need the swapon command to start using it. Usually swap
     areas are listed in /etc/fstab so that they can be taken into use at boot time by a swapon
     -a command in some boot script.

WARNING

     The swap header does not touch the first block. A boot loader or disk label can be there,
     but it is not a recommended setup. The recommended setup is to use a separate partition
     for a Linux swap area.
     mkswap, like many others mkfs-like utils, erases the first partition block to make any
     previous filesystem invisible.
     However, mkswap refuses to erase the first block on a device with a disk label (SUN, BSD,
     ...).

OPTIONS

  1. c, –check

Check the device (if it is a block device) for bad blocks before creating the swap

         area. If any bad blocks are found, the count is printed.
  1. f, –force

Go ahead even if the command is stupid. This allows the creation of a swap area larger

         than the file or partition it resides on.
         Also, without this option, mkswap will refuse to erase the first block on a device
         with a partition table.
  1. L, –label label

Specify a label for the device, to allow swapon by label.

  1. -lock[=mode]

Use exclusive BSD lock for device or file it operates. The optional argument mode can

         be yes, no (or 1 and 0) or nonblock. If the mode argument is omitted, it defaults to
         "yes". This option overwrites environment variable $LOCK_BLOCK_DEVICE. The default is
         not to use any lock at all, but it’s recommended to avoid collisions with udevd or
         other tools.
  1. p, –pagesize size

Specify the page size (in bytes) to use. This option is usually unnecessary; mkswap

         reads the size from the kernel.
  1. U, –uuid UUID

Specify the UUID to use. The default is to generate a UUID.

  1. v, –swapversion 1

Specify the swap-space version. (This option is currently pointless, as the old -v 0

         option has become obsolete and now only -v 1 is supported. The kernel has not
         supported v0 swap-space format since 2.5.22 (June 2002). The new version v1 is
         supported since 2.1.117 (August 1998).)
  1. -verbose

Verbose execution. With this option mkswap will output more details about detected

         problems during swap area set up.
  1. h, –help

Display help text and exit.

  1. V, –version

Display version information and exit.

ENVIRONMENT

     LIBBLKID_DEBUG=all
         enables libblkid debug output.
     LOCK_BLOCK_DEVICE=<mode>
         use exclusive BSD lock. The mode is "1" or "0". See --lock for more details.

NOTES

     The maximum useful size of a swap area depends on the architecture and the kernel version.
     The maximum number of the pages that is possible to address by swap area header is
     4294967295 (32-bit unsigned int). The remaining space on the swap device is ignored.
     Presently, Linux allows 32 swap areas. The areas in use can be seen in the file
     /proc/swaps.
     mkswap refuses areas smaller than 10 pages.
     If you don’t know the page size that your machine uses, you may be able to look it up with
     cat /proc/cpuinfo (or you may not - the contents of this file depend on architecture and
     kernel version).
     To set up a swap file, it is necessary to create that file before initializing it with
     mkswap, e.g. using a command like
         # dd if=/dev/zero of=swapfile bs=1MiB count=$((8*1024))
     to create 8GiB swapfile.
     Please read notes from swapon(8) about the swap file use restrictions (holes,
     preallocation and copy-on-write issues).

SEE ALSO

     fdisk(8), swapon(8)

REPORTING BUGS

     For bug reports, use the issue tracker at https://github.com/karelzak/util-linux/issues.

AVAILABILITY

     The mkswap command is part of the util-linux package which can be downloaded from Linux
     Kernel Archive <https://www.kernel.org/pub/linux/utils/util-linux/>.